Karta Vintov Dlya Iphone 5s Pdf
The below step-by-step guide walks you through how to totally disassemble the new smartphone. The following the comprehensive instructions we have provided will assist you to safely replace not only a broken iPhone 6 display assembly (LCD & touch screen), it will also help with any other internal components (i.e. Rear-facing camera, lightning connector & headphone jack assembly, power button cable, etc.) that may have become damaged or broken. 1) First, there are two Pentalobe screws located on the bottom of the iPhone 6, next to the lightning port, that need to be removed.
La nipote 1974 torrent download. You should Utilize the 5-point Pentalobe screwdriver & remove the screws from the smartphone. 2) Next, you can place a suction cup on the display assembly near, but not on top of, the home button at the bottom.
Pull up on the suction cup until there is room to insert the plastic pry opening tool in the seam between the display assembly & the rear case of the iPhone 6. Now Utilizing both tools separate the display assembly from the rear case to take a peek inside the new Apple smartphone. 3) Once you have separated the display assembly from the rear case, the metal cover that secures the LCD & front panel/digitizer cables will now be easily accessible. Next Locate & remove the five small Phillips screws (#00) that secure the metal cover (marked with orange circles). Now Gently lift up & remove the metal cover from the Apple iPhone 6.
4) Next, using the fine tip curved tweezers or spudger pry up & disconnect the four connections located under the metal cover (marked with the orange rectangles). These connections are for the display assembly (LCD and touch screen), home button assembly & the front-facing camera assembly.
Figure 17-13 iPhone 5s & iPhone SE Dimensional Drawing. Install both screws at the top of the lug as seen in Figure 8-3 (page 52) using the following.
The Home Button Assembly 5) Next Locate & remove the two small Phillips screws (#00) that secure the home button assembly & metal bracket to the display assembly (marked with orange circles). Now Use a heat gun or a blow dryer to soften the adhesive which secures the home button assembly in place, & then with the fine tip curved tweezers peel up & remove the home button assembly from the iPhone 6. This rubber gasket around the home button is easy to tear, so be careful. Earpiece Speaker and Front-Facing Camera Assembly 6) Locate & remove the three very small Phillips screws (#00) that secure the metal bracket that protects & secures the earpiece speaker in place (they are marked with orange circles). 7) Once the metal bracket is lifted or removed, lift up & remove the earpiece speaker from the Apple iPhone 6. Now, use the fine tip curved tweezers to remove the front-facing assembly from the phone.
Display Assembly (LCD and Touch Screen Digitizer) 8) Now, locate & remove the seven small Phillips screws (#00) that secure the LCD shield to the display assembly (these are marked with orange circles). Next, use a heat gun or blow dryer to soften the adhesive that secures the home button connector (this is marked with orange arrow). Now Carefully lift the connector from the adhesive securing it down, & then remove the LCD shield. SIM Card Tray 9) Use the SIM card ejection tool or a paper clip to remove the SIM card tray from the Apple iPhone 6.
Battery 10) Locate & remove the two very small Phillips screws (#00) that secure the protective metal cover over the battery connection (these are marked with orange circles). Now, use the fine tip curved tweezers or the spudger to disconnect the battery connection under the protective metal cover of the phone. 11) There is an adhesive that secures the battery to the back case of the Apple iPhone. Now Use the pull tabs on the bottom of the battery to VERY CAREFULLY remove the battery from the phone. If it is pulled correctly it will eliminate the troubles of using a heat gun or a blow dryer to soften the adhesive securing the battery in place & coaxing it out with the spudger or the plastic pry tool.
Rear-Facing Camera and Antenna 12) Locate & remove the two Phillips screws (#00) that secure the metal protective cover over the rear-facing camera (marked with orange circles). Next, use the fine tip curved tweezers to disconnect the rear-facing camera’s cable (marked with an orange rectangle) & remove it from the Apple iPhone 6. 13) Now, locate & remove the six Phillips screws (#00) which secure the protective cover over the power & volume button cable connections & antenna (marked with orange circles). 14) Next, lift & remove the antenna from the Apple iPhone 6.