The SVT-3 PRO amplifier is an ideal companion to the Classic Series, Pro Series, or PF cabinets, available separately. Like all Ampeg products, your SVT-3 PRO amplifier is designed by musicians and built using only the best of components. Each amplifier is tested to confirm that it meets our.

My programmer is trying to convince me to move to.net from PHP. Raspisanie filjmov v kinoteatre charli cherkessk youtube. [url=pharmacy viagra brand[/url] northwestpharmacy highest rated canadian pharmacies •.

Yeah Platefire's got one in over my head but I will give it my best shot! Hope we got some SVT Classic experts around? I easily found a manual and schematics on the net for it. I've been studying it trying to get a general understanding of how it works. The serial number is TCLDI800007.

Customer said he thinks it was made in the 90's, he bought it from a friend. He said the problem is that shortly after being poweing up it automaticly goes into 'red' standby/Fault which means high voltage B+ is cut off becuse of a problem detected.

I did my first test tonight with it hooked up to a single 12' 100watt speaker. It powered up fine with stanby on. Teri akhiyon ka war song free download full.

After I flipped stanby off it stayed red for a few seconds(no B+) and then went green(B+operating). I ran the amp quite a while and it never went into cutoff/Fault(red).

Checking the back panel, it has two bias pots with red & green LED's over each pot to set bias with. Bias #1 controls left three tubes, bias#2 the right three tubes. Bias #2 stays green which means correct bias setting but bias #1 has the red & green stays on all the time which the manual says it is a possible bad bias control or bad tubes. I checked the tubes on my TV-7A/U and one 6550 tested bad. I re-installed with all good tubes but the red & green bias LED's stays on. So the amp seems to be running pretty good with no red plating and my guitar sound good through it.

So---------- 1-Not getting it to go into cutoff like customer said was a problem. Could the difference be in my 1-12 cab and his large bass speaker cab? 2-On the bias, all tubes are good covered by bias pot #1---hard to believe the bias pot is bad? LooseChange Yep!

I tried setting the bias. On side #1 that is showing the problem with a solid red & green(manual says 'Possible bad Bias Control or bad tubes')--if you turn the bias counterclockwise the red comes on and hum increases. The manual says a solid red only is 'One or more tubes not functioning'. OK-the customer gave me two new EH 6550's to use.

I did find one of the existing TUNG-SOL's in the left three tubes under #1 bias with a bad reading on my TV-7A/U. I did check the EH's also and they checked good. I put the two new EH's in plus one high reading TUNG-SOL's I pulled. No change in the in the bias readout on #1--still does what I described above. I did try setting the #2 bias that is set at about 12:00 oclock showing a solid green(good). Hum increases if you go clockwise or counterclockwise from original position and the green light goes off but comes back when you return to 12:00.

The problem side #1 is set at 12:00(same as #2) and hum increases if you go either way away from that---soundwise it's happy set same as #2. It also runs normal soundwise for my 30 minuet test at one time without going into cutoff on the standby like the customer said he was having a problem with.

So according to the manual---if it's not a bad tube it's a possible bad bias control? I haven't pulled anything yet, this will be a bugger to work on.

I've never seen transformers so large!! This problem can occur in the CL if there is a fault in the output or bias circuit. Something that commonly causes this is a bad screen resistor. There should be a 220 ohm, 1/2W, flameproof, 5% resistor on each screen. Older versions had a 22 ohm resistor, some had a diode in parallel. There was a technical note issued by Loud stating to remove the diode and install the 220 ohm resistor.

I'd check those as well as the plate resistors. Running the amp at a low level might not reveal the fault problem. If you have a 4 ohm 300W dummy load, it would allow you to turn it up. Hope that this helps. On Drawing 075419-11 Sheet 1 of 2 Power Amp Pictorial is says: 'TO ADJUST BIAS-Allow to warm up for 20 Minutes.